Eibach ERS 10.00 in. Length x 3.00 in. ID Coil-Over Spring
Eibach ERS 10.00 in. Length x 3.00 in. ID Coil-Over Spring
A$198.11
Available from MFR.
This item is available from the manufacturer's distribution centre. The dispatch timeframe shown is an estimate based on historical order processing and release times for this part. This item is not held in our own warehouse, and actual dispatch timing may vary depending on manufacturer workload and logistics at the time of ordering.
We accept
Description
Eibach coilover springs are among the finest in the world and used by top race teams from F1 to WRC, and Le Mans to NASCAR. When other springs sag or need frequent replacement—these teams inevitably turn to Eibach. Producing springs with unparalleled precision and repeatability, Eibach uses the world's finest Hi-Ten spring steel, exceedingly precise tolerances, and state-of-the-art technology in every step of the manufacturing process. The coilovers are available in hundreds of sizes, spring rates, and other options. .
Product features:
* Ultra-lightweight for reduced unsprung mass
* Maximum travel, in combination with smallest block heights
* Exceptional block resistance and durability
* Precision parallel and square end configurations under unloaded and loaded conditions
* Lowest side loads with load center ideally located relative to spring axis
* Precision tolerances—the tightest in the industry
* Highest linearity and rate consistency
* Each spring individually tested and rated
Product Overview
A properly tuned spring system provides the muscle needed to transform the power derived from the engine of a racing car to the track through optimum adhesion. Suspension tuning is a precise balance. On one hand, the spring system should be soft enough to compensate for road irregularities assuring permanent road contact, while on the on the other hand the spring system must be firm enough to reduce the body roll, squat, and dive of the vehicle during cornering, acceleration and braking.
For optimum balance, Eibach has developed our world famous ERS double spring system. By combining more than 700 different single spring components, the suspension engineer or weekend enthusiast can create nearly unlimited combinations. Our ERS double-spring system is unsurpassed in performance and flexibility.
The ERS systems relies on a Main and Tender spring concept that provides a softer initial rate when both springs are compressed together, then delivers the desired firmer ending rate once the tender spring closes completely. The Main spring has a linear-rate characteristic and determines the final rate of the system. The Tender springs are available in a variety of linear-rate as well as progressive-rate characteristics and determine the initial rate of the system.
A Helper spring is used to prevent the Main spring from becoming loose in the spring seat when the wheel is at full droop. The Helper spring, unlike the Tender spring, has very little spring rate, and therefore has no effect on the suspension characteristics of the vehicle. Up to 50mm of spring-to-perch gap can be covered with the use of a Helper spring.
Connecting Plates are used to connect Main and Tender springs. Eibach offers both inside and outside diameter connection plates depending upon the dimension and function of the specific damper utilized.
* Uncountable individual combination possibilities to create from standard spring components ex stock
* High spring travel (deflection) and therefore high end loads at short mounting lengths
* Block resistance
* Surface treated through shot-peening
* High dynamic durability (component longevity)
* Precise tolerances
* High quality corrosion protection by phosphating and epoxy coating
* Individual protective packaging
* Easy identification (imprinted with Part no.-indicates spring rate and physical dimensions)
Product Details
| Block Height: | 2.83in |
|---|---|
| Description: | Off Road Spring (Silver) |
| ID: | 3.00in |
| Length: | 10.00in |
| Load @ Block Height: | 716lbs |
| Part Number: | eib1000.300.0100S |
| Rate: | 100lbs/in |
| Travel: | 7.17in |
Part Type
Coilover Springs
Specifications
- Product Attributes - UPC
- 803050287946
- Product Attributes - Brand
- Eibach
- Product Attributes - Notes
- Block height: 2.830 inch, Load at block height: 717 pounds, travel is 7.170 inch.
- Product Attributes - Quantity
- Sold individually.
- Product Attributes - Part Type
- Coilover Springs
- Product Attributes - Product Line
- Eibach Coilover Springs
- Product Attributes - Spring Finish
- Gray/Silver
- Product Attributes - Progressive Rate Spring
- No
- Product Attributes - Manufacturer's Part Number
- 1000.300.0100S
- Product Attributes - Coilover Spring Length (mm)
- 254.00mm
- Product Attributes - Coilover Spring Length (in.)
- 10.000 in.
- Product Attributes - Coilover Spring Rate (lbs/in)
- 100 lbs./in.
- Product Attributes - Coilover Spring Inside Diameter (mm)
- 76.20mm
- Product Attributes - Coilover Spring Inside Diameter (in.)
- 3.000 in.
Reference Information
| Brand Name/s | Eibach |
|---|---|
| StreetFX SKU | eib1000.300.0100S |
| SFX Item ID | 4419992 |
| Supplier Item Code | 4419992 |
| Manufacturer SKU | 1000.300.0100S |
| Manufacturer UPC | 803050287946 |
Compatibility
| Application Data |
|
|---|
Loading compatibility information...
Keep shopping
More from Eibach
Eibach
Eibach Pro-Truck Coilover Stage 2R 14-18 Chevrolet Silverado 1500 4WD
eibE86-23-032-02-22
A$2,887.26
