Edelbrock
Edelbrock Carburetor Performer Series 4-Barrel 600 CFM Electric Choke Satin Finish
ede1406
A$1,054.71
Edelbrock Pro Flo 4 Fuel Injection Kit Seq Port BBF 429/460 68-87 625 Max HP 35 LbHr Injectors Satin
Edelbrock Pro Flo 4 Fuel Injection Kit Seq Port BBF 429/460 68-87 625 Max HP 35 LbHr Injectors Satin
A$5,859.36
Limited Availability from MFR
Limited stock available from the manufacturer's distribution centre. The dispatch timeframe shown is an estimate based on historical orders of this part. This item is not held in our own warehouse, and availability and release timing may vary depending on manufacturer stock movements and processing at the time of ordering.
We accept
Description
The new Pro-Flo 4 EFI System #35680 for Ford 429/460 engines is an advanced sequential-port electronic fuel injection for the 385-series big-blocks manufactured from 1968 through 1987. This EFI is a direct bolt on and incorporates a single-plane Victor-style intake manifold with a square-bore 4150-style throttle body. The Pro-Flo 4 EFI #35680 is compatible with factory-style cylinder heads but optimized for use with Edelbrock Performer and Victor Jr. heads. The Pro-Flo 4 manifold comes preassembled and ready to run with throttle body, 42 lb/hr injectors and fuel rails. Also included is a single-connection distributor designed to work specifically with Pro-Flo 4 providing fully sequential direct-port injection and infinite control over ignition and fuel events under all conditions. This system is rated for 625 horsepower at 43 PSI with all supporting sensors, ECU, wire harnesses and 7-inch Android tablet included for a streamlined installation. Key Pro-Flo 4 advancements are its Self-Calibrating Fuel Map Technology, Wide-Band O2 Closed Loop Mixture Control, and new low-profile ECU with faster processor and upgraded Bluetooth chip for reliable connectivity with the E-Tuner app that comes preinstalled on the tablet. The E-Tuner includes a Setup Wizard to guide you through setup and provides fuel and spark adjustability for complete control over the system. Pro-Flo 4 EFI requires no laptop tuning. Minimal setup and tuning adjustments are required with base calibrations provided in the software. The ECU is self-learning and will continually adjust the fuel injection calibration for maximum performance by maintaining a specified target air-fuel ratio as you drive. The E-Tuner provides the ability to fine-tune air-fuel ratios, ignition curve, idle speed, acceleration fuel, fans, rev-limiter and more. Multiple displays let you monitor engine performance in real-time from inside or outside of the vehicle while retaining the simplicity that Pro-Flo 4 systems are known for.
Product Overview
The new Pro-Flo 4 EFI System #35680 for Ford 429/460 engines is an advanced sequential-port electronic fuel injection for the 385-series big-blocks manufactured from 1968 through 1987. This EFI is a direct bolt on and incorporates a single-plane Victor-style intake manifold with a square-bore 4150-style throttle body. The Pro-Flo 4 EFI #35680 is compatible with factory-style cylinder heads but optimized for use with Edelbrock Performer and Victor Jr. heads. The Pro-Flo 4 manifold comes preassembled and ready to run with throttle body, 42 lb/hr injectors and fuel rails. Also included is a single-connection distributor designed to work specifically with Pro-Flo 4 providing fully sequential direct-port injection and infinite control over ignition and fuel events under all conditions. This system is rated for 625 horsepower at 43 PSI with all supporting sensors, ECU, wire harnesses and 7-inch Android tablet included for a streamlined installation. Key Pro-Flo 4 advancements are its Self-Calibrating Fuel Map Technology, Wide-Band O2 Closed Loop Mixture Control, and new low-profile ECU with faster processor and upgraded Bluetooth chip for reliable connectivity with the E-Tuner app that comes preinstalled on the tablet. The E-Tuner includes a Setup Wizard to guide you through setup and provides fuel and spark adjustability for complete control over the system. Pro-Flo 4 EFI requires no laptop tuning. Minimal setup and tuning adjustments are required with base calibrations provided in the software. The ECU is self-learning and will continually adjust the fuel injection calibration for maximum performance by maintaining a specified target air-fuel ratio as you drive. The E-Tuner provides the ability to fine-tune air-fuel ratios, ignition curve, idle speed, acceleration fuel, fans, rev-limiter and more. Multiple displays let you monitor engine performance in real-time from inside or outside of the vehicle while retaining the simplicity that Pro-Flo 4 systems are known for.
Features and Benefits
- New ECU Preloaded w/80 Dyno-Tuned Calibrations
Product Details
| Bore Diameter: | 1.75 |
|---|---|
| Cylinder Head Type: | Sequential Port |
| Description: | Pro-Flo 4 Fuel Injection Kit |
| Distributor Cap Included: | Yes |
| Engine Make/Size: | Chrysler Hemi Gen III |
| Finish: | Satin |
| Flange Type: | 4150 |
| Fuel Injector Type: | 42 lb/hr |
| Fuel Pressure Port: | 1/8-27 NPT |
| Fuel Rate: | 42 lbs./hr |
| Gasket Or Seal Included: | Yes |
| Idle Air Control Motor Included: | Yes |
| Manifold Height: | 4.25 |
| Maximum Horsepower: | 675 |
| Part Number: | ede35680 |
| Quantity: | Kit |
| RGL: | WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov. |
| System Type: | Traditional 4150-Style Kit |
| Throttle Body Type: | 4 Barrel |
| WARNING CA Proposition 65 Message: | WARNING: This product can expose you to Lead; which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information; visit www.P65warnings.ca.gov. |
| WARNING CA Proposition 65: | Yes |
| Wire Harness Included: | Yes |
| Wiring Harness Included: | Yes |
Application Summary
Ford:Big-Block:429 (7.0L )-460 (7.5L)
Part Type
Fuel Injection System
Features
- New ECU Preloaded w/80 Dyno-Tuned Calibrations
Specifications
- Product Attributes - Brand
- Edelbrock
- Product Attributes - Manufacturer's Part Number
- 35680
- Product Attributes - Part Type
- Fuel Injection Systems
- Product Attributes - Product Line
- Edelbrock Pro-Flo 4 EFI Systems
- Product Attributes - UPC
- 085347356805
- Product Attributes - Fuel Injection Style
- Multi-port
- Product Attributes - Fuel Injection System Type
- Single 4-Barrel Throttle Body (4150 Flange)
- Product Attributes - Maximum Horsepower with Gas
- 675
- Product Attributes - Timing Control Compatible
- Yes
- Product Attributes - ECM Included
- Yes
- Product Attributes - Self Tuning
- Yes
- Product Attributes - User Tunable
- Yes
- Product Attributes - Fuel System Included
- None
- Product Attributes - Ignition System Included
- Distributor
- Product Attributes - Power Distribution Included
- None
- Product Attributes - User Interface Included
- Bluetooth
- Product Attributes - EGR
- No
- Product Attributes - Transmission Controller Included
- No
- Product Attributes - Metering Style
- Speed density
- Product Attributes - Intake Material
- Aluminum
- Product Attributes - Intake Color
- Natural
- Product Attributes - Engine Block Deck Height
- Standard deck
- Product Attributes - Multi-Port Fuel Rails Included
- Yes
- Product Attributes - Throttle Body Included
- Yes
- Product Attributes - Throttle Body Mounting Flange
- 4-barrel square bore
- Product Attributes - Venturi Quantity
- 4
- Product Attributes - Venturi Diameter (mm)
- 44.45mm
- Product Attributes - Airflow Rate (cfm)
- 1,000 cfm
- Product Attributes - Throttle Body Material
- Cast aluminum
- Product Attributes - Throttle Body Color
- Natural
- Product Attributes - Injectors Included
- Yes
- Product Attributes - Injector Size (lbs/hr)
- 42 lbs./hr.
- Product Attributes - Calibration Module Included
- No
- Product Attributes - Wiring Harness Included
- Yes
- Product Attributes - Oxygen Sensor Included
- Yes
- Product Attributes - Fuel Pressure Regulator Included
- No
- Product Attributes - MAP Sensor Included
- Yes
- Product Attributes - IAT Sensor Included
- Yes
- Product Attributes - TPS Sensor Included
- Yes
- Product Attributes - IAC Motor Included
- Yes
- Product Attributes - Quantity
- Sold as a kit.
- Product Attributes - Notes
- Supports up to 675 HP. Tuning and set-up app can be downloaded to a Bluetooth capable tablet or smart phone from either the Apple or Google app stores. Use with boosted applications requires a 2-bar MAP sensor.
Reference Information
| Brand Name/s | Edelbrock |
|---|---|
| StreetFX SKU | ede35680 |
| SFX Item ID | 4237599 |
| Supplier Item Code | 4237599 |
| Manufacturer SKU | 35680 |
| Manufacturer UPC | 85347356805 |
| Alternative References | EDB35680, EDL-35680 |
Brochures
Compatibility
Ford:Big-Block:429 (7.0L )-460 (7.5L)
Loading compatibility information...
Keep shopping
More from Edelbrock
Edelbrock
Edelbrock Supercharger Stage 1 - Street Kit 2016 Mazda MX-5 Miata 2.0L w/ Tune
ede1554
A$14,207.84
Edelbrock
Edelbrock Crate Engine Supercharged Gen2 Coyote 5.0L w/8-Rib Belt Drive & Electronics (R2650-DP3C)
ede46890
A$64,128.94
Edelbrock
Edelbrock Power Package Top End Kit E-Street and Performer SBC
ede2022
A$5,158.44
A$5,543.43