Edelbrock
Edelbrock Carburetor Performer Series 4-Barrel 600 CFM Electric Choke Satin Finish
ede1406
A$1,054.71
Edelbrock Pro Flo 4 EFI System Seq Port Chrysler Gen II Hemi 426-572 950 Max HP 60lb/hr Satin Finish
Edelbrock Pro Flo 4 EFI System Seq Port Chrysler Gen II Hemi 426-572 950 Max HP 60lb/hr Satin Finish
A$7,458.13
Available from MFR.
This item is available from the manufacturer's distribution centre. The dispatch timeframe shown is an estimate based on historical order processing and release times for this part. This item is not held in our own warehouse, and actual dispatch timing may vary depending on manufacturer workload and logistics at the time of ordering.
We accept
Description
Pro-Flo 4 Dual-Quad HEMI EFI System #35670 is intended for use with1964-71 Mopar Gen II 426-572 HEMI engines operating in the 2,500-6,500+ RPM range. This EFI incorporates a single-plane Air-Gap design manifold with dual square-bore 4150-style throttle bodies that bolts directly onto vehicles with a shaker hood. The Dual-Quad HEMI EFI manifold is compatible with factory-style cylinder heads but optimized for use with Victor Jr. HEMI heads. Manifold comes preassembled and ready to run with throttle bodies, 60 lb/hr injectors and fuel rails. Also included is a single-connection distributor designed to work specifically with Pro-Flo 4 providing fully sequential-port injection and infinite control over ignition and fuel events under all conditions. This system is rated for 825 horsepower at 43 PSI with all supporting sensors, ECU, wire harnesses and 7-inch Android tablet included for a streamlined installation. Key advancements of Pro-Flo 4 EFI are its Self-Calibrating Fuel Map Technology, Wide-Band O2 Closed Loop Mixture Control, and new low-profile ECU with faster processor and upgraded Bluetooth chip for reliable connectivity with the E-Tuner app that comes preinstalled on the tablet. The E-Tuner includes a Setup Wizard to guide you through setup and provides fuel and spark adjustability for complete control over the system. Pro-Flo 4 EFI does not require laptop tuning. Minimal setup and tuning adjustments are required with base calibrations provided in the software. The ECU is self-learning and will continually adjust the fuel injection calibration to get the maximum performance out of your engine by maintaining a specified target air-fuel ratio as you drive. The E-Tuner provides the ability to fine-tune air-fuel ratios, ignition curve, idle speed, acceleration fuel, fans, rev-limiter and more. Multiple displays let you monitor engine performance in real-time from inside or outside of the vehicle while retaining the simplicity that Pro-Flo 4 systems are known for.
Product Overview
Pro-Flo 4 Dual-Quad HEMI EFI System #35670 is intended for use with1964-71 Mopar Gen II 426-572 HEMI engines operating in the 2,500-6,500+ RPM range. This EFI incorporates a single-plane Air-Gap design manifold with dual square-bore 4150-style throttle bodies that bolts directly onto vehicles with a shaker hood. The Dual-Quad HEMI EFI manifold is compatible with factory-style cylinder heads but optimized for use with Victor Jr. HEMI heads. Manifold comes preassembled and ready to run with throttle bodies, 60 lb/hr injectors and fuel rails. Also included is a single-connection distributor designed to work specifically with Pro-Flo 4 providing fully sequential-port injection and infinite control over ignition and fuel events under all conditions. This system is rated for 825 horsepower at 43 PSI with all supporting sensors, ECU, wire harnesses and 7-inch Android tablet included for a streamlined installation. Key advancements of Pro-Flo 4 EFI are its Self-Calibrating Fuel Map Technology, Wide-Band O2 Closed Loop Mixture Control, and new low-profile ECU with faster processor and upgraded Bluetooth chip for reliable connectivity with the E-Tuner app that comes preinstalled on the tablet. The E-Tuner includes a Setup Wizard to guide you through setup and provides fuel and spark adjustability for complete control over the system. Pro-Flo 4 EFI does not require laptop tuning. Minimal setup and tuning adjustments are required with base calibrations provided in the software. The ECU is self-learning and will continually adjust the fuel injection calibration to get the maximum performance out of your engine by maintaining a specified target air-fuel ratio as you drive. The E-Tuner provides the ability to fine-tune air-fuel ratios, ignition curve, idle speed, acceleration fuel, fans, rev-limiter and more. Multiple displays let you monitor engine performance in real-time from inside or outside of the vehicle while retaining the simplicity that Pro-Flo 4 systems are known for.
Features and Benefits
- New ECU Preloaded w/80 Dyno-Tuned Calibrations
Product Details
| Bore Diameter: | 1.75 |
|---|---|
| Description: | Pro-Flo 4 Fuel Injection Kit |
| Distributor Cap Included: | Yes |
| Finish: | Satin |
| Flange Type: | 4150 |
| Fuel Injector Type: | 60 lb/hr |
| Fuel Pressure Port: | 1/8-27 NPT |
| Fuel Rate: | 60 lbs./hr |
| Gasket Or Seal Included: | Yes |
| Idle Air Control Motor Included: | Yes |
| Manifold Height: | 5.10 |
| Maximum Horsepower: | 825 |
| Part Number: | ede35670 |
| Quantity: | Kit |
| RGL: | WARNING: This product can expose you to Lead, which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information, visit www.P65warnings.ca.gov. |
| System Type: | Traditional 4150-Style Kit |
| Throttle Body Type: | 4 Barrel |
| WARNING CA Proposition 65 Message: | WARNING: This product can expose you to Lead; which is known to the State of California to cause cancer or birth defects or other reproductive harm. For more information; visit www.P65warnings.ca.gov. |
| WARNING CA Proposition 65: | Yes |
| Wire Harness Included: | Yes |
| Wiring Harness Included: | Yes |
Part Type
Fuel Injection System
Features
- New ECU Preloaded w/80 Dyno-Tuned Calibrations
Specifications
- Product Attributes - Brand
- Edelbrock
- Product Attributes - Manufacturer's Part Number
- 35670
- Product Attributes - Part Type
- Fuel Injection Systems
- Product Attributes - Product Line
- Edelbrock Pro-Flo 4 EFI Systems
- Product Attributes - UPC
- 085347356706
- Product Attributes - Fuel Injection Style
- Multi-port
- Product Attributes - Fuel Injection System Type
- Dual 4-Barrel Throttle Bodies (4150 Flange)
- Product Attributes - Maximum Horsepower with Gas
- 825
- Product Attributes - Timing Control Compatible
- Yes
- Product Attributes - ECM Included
- Yes
- Product Attributes - Self Tuning
- Yes
- Product Attributes - User Tunable
- Yes
- Product Attributes - Fuel System Included
- None
- Product Attributes - Ignition System Included
- Distributor
- Product Attributes - Power Distribution Included
- None
- Product Attributes - User Interface Included
- Bluetooth
- Product Attributes - EGR
- No
- Product Attributes - Transmission Controller Included
- No
- Product Attributes - Metering Style
- Speed density
- Product Attributes - Intake Material
- Aluminum
- Product Attributes - Intake Color
- Natural
- Product Attributes - Engine Block Deck Height
- Standard deck
- Product Attributes - Multi-Port Fuel Rails Included
- Yes
- Product Attributes - Throttle Body Included
- Yes
- Product Attributes - Throttle Body Mounting Flange
- 4-barrel square bore
- Product Attributes - Venturi Quantity
- 8
- Product Attributes - Venturi Diameter (mm)
- 44.45mm
- Product Attributes - Airflow Rate (cfm)
- 2,000 cfm
- Product Attributes - Throttle Body Material
- Cast aluminum
- Product Attributes - Throttle Body Color
- Natural
- Product Attributes - Injectors Included
- Yes
- Product Attributes - Injector Size (lbs/hr)
- 60 lbs./hr.
- Product Attributes - Calibration Module Included
- No
- Product Attributes - Wiring Harness Included
- Yes
- Product Attributes - Oxygen Sensor Included
- Yes
- Product Attributes - Fuel Pressure Regulator Included
- No
- Product Attributes - MAP Sensor Included
- Yes
- Product Attributes - IAT Sensor Included
- Yes
- Product Attributes - TPS Sensor Included
- Yes
- Product Attributes - IAC Motor Included
- Yes
- Product Attributes - Quantity
- Sold as a kit.
- Product Attributes - Notes
- Supports up to 825 HP; Tuning and set-up app can be downloaded to a Bluetooth capable tablet or smart phone from either the Apple or Google app stores. Use with boosted applications requires a 2-bar MAP sensor.
Reference Information
| Brand Name/s | Edelbrock |
|---|---|
| StreetFX SKU | ede35670 |
| SFX Item ID | 4237540 |
| Supplier Item Code | 4237540 |
| Manufacturer SKU | 35670 |
| Manufacturer UPC | 85347356706 |
| Alternative References | EDB35670, EDL-35670, 60lb/hr |
Brochures
Compatibility
| Application Data |
|
|---|
Loading compatibility information...
Keep shopping
More from Edelbrock
Edelbrock
Edelbrock Supercharger Stage 1 - Street Kit 2016 Mazda MX-5 Miata 2.0L w/ Tune
ede1554
A$14,207.84
Edelbrock
Edelbrock Crate Engine Supercharged Gen2 Coyote 5.0L w/8-Rib Belt Drive & Electronics (R2650-DP3C)
ede46890
A$64,128.94
Edelbrock
Edelbrock Power Package Top End Kit E-Street and Performer SBC
ede2022
A$5,158.44
A$5,543.43